Transport of electrolytic solutions under influence of electric fields occurs in phenomena ranging from biology to geophysics. Here, we present a continuum model for single-phase electrohydrodynamic flow, which can be derived from fundamental thermodynamic principles. This results in a generalized...
Thermoelectric modules can be used in waste heat harvesting, sensing, and cooling applications. Here, we report on the fabrication and performance of a four-leg module based on abundant silicide materials. While previously optimized Mg2Si0.3Sn0.675Bi0.025 is used as the n-type leg, we employ a...
An accurate description of the radiation quality of proton beams is a precondition to increase our understanding of radiobiological mechanisms and to develop accurate biological response models for radiotherapy. However, there are few detectors capable of measuring microdosimetric quantities with...
This paper describes the application of neural network approaches to the discovery of new materials exhibiting thermoelectric properties. Thermoelectricity is the ability of a material to convert energy from heat to electricity. At present, only few materials are known to have this property to a...
Nanoporous amorphous silicon (a-Si) with <5 nm cylindrical pores have been fabricated by phase separation of aluminum (Al) and silicon, forming self-assembled Al nanowires (NWs), followed by subsequent removal of Al by wet etching. This work studies the removal process of the Al NWs when using the...
Magnetic properties of High-Entropy Alloys based on the Fe-Co-Ni-Al-Mn system are reported. High-Entropy Alloys are cutting-edge technological materials containing five or more elements in relatively high concentrations (5–35 at.%) within one or several solid-state solutions. These solutions are...
Hydrogen effect on fatigue performance of commercially pure BCC iron has been studied with a combination of various electron microscopy techniques. The fatigue crack growth (FCG) in gaseous hydrogen was found to consist of two regimes corresponding to a slightly accelerated regime at relatively low...
Hydrogen effect on fatigue performance at relatively high values of stress intensity factor range, ΔK, of pure BCC iron has been studied with a combination of various electron microscopy techniques. Hydrogen-assisted fatigue crack growth rate is manifested by a change of fracture features at the...
Process conditions during catalytic reactions induce significant changes in surface chemistry and structure of bi- (mono) metallic nanoparticles leading to their deactivation, and this can ultimately affect the reactions long-term performance. Here PtCu and Pt model nanoparticles are prepared by...
In this work we present a significant advancement in cubic silicon carbide (3C-SiC) growth in terms of crystal quality and domain size, and indicate its potential use in photovoltaics. To date, the use of 3C-SiC for photovoltaics has not been considered due to the band gap of 2.3 eV being too large...
Water photoelectrolysis has the potential to produce renewable hydrogen fuel, therefore addressing the intermittent nature of sunlight. Herein, a monolithic, photovoltaic (PV)-assisted water electrolysis device of minimal engineering and of low (in the μg range) noble-metal-free catalysts loading is...
Concrete is the second most consumed product by humans, after water. However, the production of conventional concrete causes more than 5% of anthropogenic CO2 emissions and therefore there is a need for emission-reduced construction materials. One method to produce a solid, concrete-like...
Transition metal antimonides form a class of intermetallic compounds, which has drawn considerable attention due to their potential applications in various fields. However, the formation of nanostructures containing multiple transition metal elements has been a challenge. Here, a new class of...
In spite of their relatively high lattice thermal conductivity κℓ, the XNiSn (X=Ti, Zr, or Hf) half-Heusler compounds are good thermoelectric materials. Previous studies have shown that κℓ can be reduced by sublattice alloying on the X site. To cast light on how the alloy composition affects κℓ, we...
An all-oxide thermoelectric generator for high-temperature operation depends on a low electrical resistance of the direct p–n junction. Ca3Co4−xO9+δ and CaMnO3−δ exhibit p-type and n-type electronic conductivity, respectively, and the interface between these compounds is the material system...
We apply inline electron holography to investigate the electrostatic potential across an individual BaZr0.9Y0.1O3 grain boundary. With holography, we measure a grain boundary potential of −1.3 V. Electron energy loss spectroscopy analyses indicate that barium vacancies at the grain boundary are the...
In this work, silicon/carbon composites for anode electrodes of Li-ion batteries are prepared from Elkem’s Silgrain® line. Gentle ball milling is used to reduce particle size of Silgrain, and the resulting Si powder consists of micrometic Si with some impurities. Silicon/carbon composite with CMC...
Wafer-level thermocompression bonding (TCB) using aluminum (Al) is presented as a hermetic sealing method for MEMS. The process is a CMOS compatible alternative to TCB using metals like gold (Au) and copper (Cu), which are problematic with respect to cross contamination in labs. Au and Cu are...
The thermoelectric properties of 54 different group 4 half-Heusler (HH) alloys have been studied from first principles. Electronic transport was studied with density functional theory using hybrid functionals facilitated by the k⋅p method, while the temperature-dependent effective potential method...
Although the space charge model is commonly used to explain the high grain boundary resistance in proton conducting yttrium-substituted BaZrO3, it fails in its simplest forms with factors 10–40 to fit experimental data with respect to the characteristic frequency of the grain boundary impedance. We...